Rounded heels are said to minimize heel strike, because they allow a gradual roll from the heel to the sole instead of the jarring impact when the edge of a square-cut heel hits the ground, but I haven’t noticed any difference in practice. A shock-absorbing midsole seems far more important for reducing heel-strike injury.
Rands
The most likely place for water to penetrate a boot is where the sole and the upper meet. Some boots have a rubber rand running around this joint, while others have just toe or toe and heel rands, or bumpers. Rands seal the joint against water and also protect the lower edge of the uppers from scuffs and scratches.
Stitching versus Bonding
Joining the soles to the uppers is a critical part of footwear manufacture. If that connection fails, the shoe or boot will fall apart. Stitching used to be the only way of holding footwear together but is now used mainly in leather boots made for mountaineering or Nordic ski touring rather than for walking. The most common stitched construction is the Norwegian welt, sometimes called stitchdown construction, in which the upper is turned out from the boot, then sewn to a leather midsole with two or three rows of stitching. These stitches are visible and exposed, but they can be protected by daubing them with sealant.
Currently, on most footwear the uppers are heat bonded (glued at high temperatures) or cemented to the sole. (Some are also Blake or Littleway stitched, which means the uppers are turned in and stitched to a midsole, to which the outsole is cemented.) Unlike the Norwegian welt, the quality of these construction methods cannot be checked. A bonded sole has failed me only once, many years ago. On that occasion, the sole started to peel away from the boot at the toe after only 250 miles. I was on a long trek and far from a repair shop, so I patched the boots with glue from my repair kit almost every night and nursed them through another 500 miles. I wouldn’t like to repeat the experience.
FOOTWEAR MODELS AND CHOICES
Because fit is so crucial, I’m reluctant to recommend any specific models. I’m often asked to do so, though, so here are some hints. Over the years I’ve happily worn footwear from Adidas, Asolo, Bite, Brasher, Five Ten, Garmont, Hi-Tec, Lowa, Merrell, Montrail, Nike ACG, Raichle, Rockport, Salomon, Scarpa, Teva, The North Face, Vasque, and Zamberlan. That’s a lot of boots, shoes, and sandals. Most of the specific models I’ve used are no longer available. Well-recommended brands I’ve never tried include Alico, Birkenstock, Boreal, Chaco, Danner, Dunham, Gronell, Kayland, La Sportiva, Limmer, Technica, and Timberland.
Of the footwear I’ve tried most recently and that therefore hadn’t disappeared when I wrote this, here are my current favorites, described as examples rather than recommendations. Remember: my ideal shoe might be your worst nightmare.
Sandals
I’ve almost worn out a pair of Merrell Onos, which have a synthetic leather upper lined with stretchy neoprene and Spandex. They fasten with adjustable clip buckles. The rear section is stiffened at each side for support. The molded EVA foot-frame is soft and cushioning and shaped to support the foot. It has an antimicrobial treatment too, which works well, as I found after a sweaty nine-day hike. The tread is reasonably deep and made from sticky rubber. They weigh 27 ounces (all weights are for a pair of men’s size 9½). I’ve hiked many miles in these sandals and found them supportive and comfortable, with a good grip on just about any terrain. But the Onos have been supplanted in my affections by Teva Wraptor 2s, the first sandal I’ve tried that holds the foot in place as well as the best lightweight shoes and boots. This is achieved by an ingenious design, a strap that runs across the instep, through the sole, and then back across the instep, completely encircling the foot. Tightening this strap pulls the sandal around the arch, heel, and instep for a very secure fit. Combined with the soft, deep foot-shaped top sole, this strap also helps prevent over-pronation. The straps are padded nubuck, fastened at the forefoot, instep, and heel with Velcro. There’s a dual-density EVA midsole and a deep tread on the outsole. They weigh 2 pounds, slightly on the heavy side for sandals but worth it for the support they give. Most recently I’ve been wearing Bite X-Tracs, which have a thick polyurethane footbed that can be replaced with Superfeet or other stabilizing footbeds. These have leather uppers with neoprene linings, a cushioning midsole, and an arch shank, and they weigh 29 ounces (without footbeds). The sole is torsionally flexible and quite wide, and the tread isn’t very deep, so while they’re fine on good trails, these sandals aren’t that good on rough and steep terrain. Being able to fit Superfeet into sandals is a great idea, though, and I hope that sandals more suited to rough terrain will appear with this feature.
Bite sandal with Superfeet footbed fitted. The footbeds stabilize the feet and minimize overpronation.
Trail Shoes
For low-cut shoes I like the sliplasted Salomon XA Pros, which are quite light at 27 ounces yet stable and well cushioned. They look like standard running shoes rather than trail shoes. I first tried these on a short adventure race and was impressed that after three hours or so of running and cycling on rough, steep terrain in very hot weather, my feet felt fine. The shoes are made from mesh backed with thin foam (which makes them quick drying and very breathable, though not at all water resistant), with synthetic leather reinforcements. There’s a dual-density EVA midsole for shock absorption and an outsole made from three hardnesses of rubber. A synthetic plate between the midsole and the outsole gives lateral stiffness to the rear of the shoe while allowing the forefoot to flex easily. The laces are made of thin Kevlar with a cord lock at the top and speed-lacing hooks. One yank and they’re tight, no knots required. They can’t slip or come undone, either. The lower hooks are offset, so the shoes flex with the foot. I’d wear the XA Pros more often, except that in the weather for which they’re most appropriate, I tend to choose sandals.
I’ve also been impressed with the sliplasted Blaze Low from The North Face, a suede-fabric shoe with a molded EVA midsole and a plastic plate for torsional stiffness. The shoes breathe well and dry fast, but the mesh means they’re not very water resistant. The excellent tread has studs in the center, which help them grip on wet grass, and lugs round the edges. The cushioning is particularly good; thicker and softer than on most footwear. These shoes are excellent for long distances, and for hard terrain that pounds your feet. The heel counter is firm and the torsional stiffness means the shoes don’t twist sideways much on rough terrain. Soft forward flex makes them very comfortable. Lacing is with eyelets and webbing loops. They weigh 29 ounces.
My favorite lightweight leather boot, the Hi-Tec Sierra V-Lite.
Lightweight Boots
In theory, lightweight boots are my favorites, but I don’t seem to wear them much these days, preferring trail shoes or sandals when there’s no snow and slightly heavier boots when there is. Of the pairs I’ve tried in recent years, I like the Hi-Tec Sierra V-Lite Leather. These are made from nubuck leather with a synthetic CoolMax wicking lining. There’s a thermoplastic lasting board for torsional stiffness and an EVA midsole for good cushioning. Lacing is with four sets of tunnels and two sets of hooks. They weigh just 34 ounces, very light for leather boots. Heel to toe the boots are very flexible but on rough, steep terrain these boots give me good support due to the torsional stiffness. On one occasion I descended 3,000 feet off trail on frozen turf, rock, scree, tussocks, and wet grass with no problem. I was surprised at how good the water resistance was for such light boots. They do leak eventually but drying time is fast. Overall these feel more like trail shoes than heavier boots, with the addition of a high ankle.
Midweight Boots
Montrail’s 3-pound, 5-ounce Cristallo is a high-quality boot that does all that’s required without any bells and whistles. The Cristallo is made from nubuck with a synthetic lining. The boots have a graded nylon insole with a half-length steel shank, microporous rubber midsole, and Vibram outsole. Torsionally they are quite stiff because of the shank, but they flex well at the forefoot. They have a fairly low volume, like my feet. I did have to
stretch them slightly at the toes, however. The 3-pound, 10-ounce Scarpa Delta M3 is a similar boot, again made from nubuck with a synthetic lining. The leather is treated with silicone and oil and has proved very water resistant. There’s a Vibram sole with an EVA shock-absorbing insert in the heel plus a polyurethane midsole. As with the Cristallos, I had to stretch them at the toes to get a good fit.
I wouldn’t choose either of these boots for trail hikes in summer. They’re too stiff, warm, and heavy. I wear them for mountain hiking when there’s snow and I think I may need to use crampons or for off-trail hiking in steep, rugged, rocky terrain where I want some protection for my feet.
Heavyweight Boots
This is my least favorite category; I rarely wear boots this stiff and heavy. But I have been pleasantly surprised by the relative comfort of Scarpa Mantas. These 4-pound, 6-ounce rigid-soled boots have a rocker sole, a rigid nylon midsole with a steel insert, polyurethane cushioning, speed lacing, and a well-fitting, padded upper that makes them quite bearable, though I wouldn’t want to do a long trail hike in them. However, if there’s much hard snow and ice around and crampons are needed most of the time, they’re my first choice. The uppers are made from rough-out water-resistant leather, and the sole is a deep-cleated Vibram M4 Tech with grooves at the toe and heel so clip crampons can be fitted. The polyurethane cushioning takes some of the sting out of rocks and hard surfaces, and the slight rocker in the sole makes walking on the flat easier than with a flat-soled boot. Although the ankles are held firmly in place, they can flex forward thanks to a cutaway section below the top two lace clips, which also makes walking on the flat relatively comfortable. The overall quality of the boots is superb.
A winter-weight boot (Garmont Pinnacle).
A midweight leather boot (Montrail Cristallo).
CARE OF FOOTWEAR
Waterproofing and Sealing
Although most footwear is fairly tough, it needs proper care to ensure a long life and good performance. This care can start before you wear the boots. Sealing any exposed stitching to protect it from abrasion will increase durability and make the seams waterproof. Urethane sealers like McNett Seam Grip work well, as do products specially designed for this use, like Aquaseal Stitch Guard. Some sealants come with an applicator; others are best applied with a syringe. Stitching should be sealed before you wear or wax the footwear so that the sealant has a clean, dry surface to stick to. I always used to seal the welts of my leather Nordic ski boots so that water didn’t wick in through the stitching when the boots flexed. My plastic telemark boots don’t have stitching, and I haven’t bothered sealing the seams of other footwear.
Muddy, dirty boots need washing; if mud dries on the uppers, especially if they’re leather, they can harden and crack. A soft brush (I use an old toothbrush) helps remove mud from seams, stitching, and tongue gussets, though you should be careful not to scratch leather. I find cold tap water adequate for cleaning hiking footwear, and I don’t use soap. I’m not bothered if footwear is stained or discolored; indeed, this can add character. But if ingrained dirt is particularly stubborn or you want to remove any stains, there are specific cleaning products—Nikwax Cleaning Gel, Granger’s New Technology Footwear Cleaner, and Aquaseal All Purpose Footwear Cleaner. The first two have easy-to-use sponge applicators. You just rub them over the boots, then rinse off the foam, scrubbing with a soft nylon brush if necessary. A sink is the best place to do this.
The insides of boots can get dirty too, making them smelly and less breathable, so sweaty socks are more likely. In boots with waterproof membranes, tiny specks of grit may work their way through the lining and cut the membrane so it leaks. Just a wipe with a clean, damp cloth may be enough cleaning—it’s all I ever do. However, Nikwax suggests filling boots with water and leaving them to soak overnight before emptying them out and rinsing them.
Water-based footwear products are easy to apply and produce no pollution, since they contain no solvents.
Excessive heat is very likely to make leather harden and split and may melt the glues that hold footwear together. Wet footwear should never be dried in a hot place such as next to a car heater, a house radiator, or a campfire. Leather should never become too hot to touch. Even midday sunshine can be too warm, and if you stay in a mountain hut or hostel with a drying room, you should keep your footwear out of there. Footwear should be left in a cool, dry place to dry slowly, with the insoles removed and the tongues fully open. If shoes are really soaked, stuffing them with newspaper will help them dry. Replace the paper when it gets really wet. Fabric-leather shoes without internal padding dry quickly, but foam-lined leather boots can take a long time—at least several days for medium-weight ones.
Drying footwear can be a problem on long hikes, when it is tempting to dry sodden boots by a fire. I’m occasionally guilty of this. The second half of a Canadian Rockies walk was mostly cross-country in wet terrain, and my lightweight leather boots were soaked by the end of most days. I often helped them dry out by standing them a little too close to my campfire. I had to wear boots with cracked uppers and peeling soles for the last few snowy weeks of the hike.
When wet footwear has dried, it needs to be treated to restore suppleness and water repellency. Bootmakers recommend various products for this, sometimes proprietary ones. It isn’t necessary to stick to the treatment specified. All footwear can be treated, including that with waterproof-breathable linings. Indeed, because such linings work well only if the outer of the boot is breathable, it is important that the water repellency of the outer is maintained. If it fails and the outer soaks up moisture, breathability will be impaired. Remove the laces and open the tongue fully so you don’t miss any areas. The base of the tongue is a key leak point, so make sure you treat this area.
Once it’s no longer part of a living animal, leather isn’t waterproof. It’s treated with water-proofing compounds during tanning, but this treatment will wear off after a few hikes, especially in wet conditions. Proper treatment increases water repellency and prolongs life by keeping leather footwear supple. What constitutes proper treatment depends in part on the type of leather. Virtually all leathers are now chemically treated rather than oil tanned, and they must be dressed with wax or the new water-based treatments rather than oil. Traditional dressings like neat’s-foot oil (made by boiling down cattle feet and shinbones) or mink oil can oversoften leather; I’d use them only for leather that has dried out and hardened. Even then I’d rather use a modern softening product like Nikwax Conditioner for Leather. Makers sometimes suggest not treating specially tanned waterproof leathers until they are scuffed, since they won’t absorb proofing before then. Others say all leather should be treated before the first use. I have found that new boots won’t absorb much treatment, so I don’t bother applying any until the leather loses the initial sheen or water starts to soak into it rather than bead up.
The traditional way to proof leather boots is to apply a soft wax with a cloth or your fingers. Granger’s G-Wax, Sno-Seal, and Biwell Classic are made from beeswax, while Nikwax Paste Wax is a synthetic mineral wax and Aquaseal Leather Waterproofing is silicone based. These waxes work best when applied to warm, dry leather and left to soak in overnight. Any residue visible on the surface should be wiped off. Several thin coats are more effective than one thick one. Too much can soften the leather anyway, so it’s best not to slop the stuff on in dollops. Also, a thick layer of wax can prevent your boots from breathing and lead to sweaty feet. There is a trade-off between the amount of wax you apply, the degree of water resistance obtained, and the breathability of your boots. Several layers of wax will mean better and longer-lasting water resistance but less breathability. In hot weather I’d go easy on the wax, or your feet will get wetter from sweat than from the occasional summer shower. Even for desert hiking I still treat leather, though, to prevent it from drying out and cracking.
There’s something sensuous about applying wax to warm leather with your fingers (I prefer fingers to a cloth bec
ause their heat helps soften the wax), but I rarely do this anymore because there are much better water-based products. It may seem odd that a waterproofing product’s main ingredient is water, but it does work. Water-based treatments were first developed by Nikwax, which makes the widest range, and you can now get them from Granger’s too. Others will follow, I’m sure. Nikwax water-based treatments consist of polymers made from EVA (the same material used for cushioning midsoles) and mineral wax. The active ingredients take the form of an emulsion—droplets of oil suspended in water. Nikwax treatments coat the fibers of leather and fabric with flexible water-repellent molecules. These molecules will stick only to fibers that aren’t already water repellent, so you can’t apply too much. The water soaks into areas that aren’t water repellent, taking the active ingredients with it. Water-based treatments can be applied to wet leather; indeed, Nikwax says it’s best to do so, since the active ingredients are then drawn into those areas that need them most. It’s certainly convenient not to have to dry footwear before treating it. Water-based treatments don’t block the spaces between the fibers, so footwear remains breathable. And because they can flex, they don’t wear off quickly. Water-based products have other advantages. Nikwax says its products can deliver up to five times as many active ingredients per fluid ounce as solvent-based treatments. Water-based products are also environmentally friendly; they contain no petroleum solvents or propellant gases, which contribute to global warming and to the thinning of the ozone layer. The absence of solvents also means water-based products are nonflammable and don’t give off noxious fumes, so they are safe to use indoors.
Chris Townsend Page 10
